Suggestions

Deaeration Valve Assembly

ProMinent’s de-aeration valve assembly helps evacuate gases from pumps, preventing system backpressure and maintaining optimal pump operation. It allows accumulated gases to exit via the bleed valve, ensuring a consistent flow of liquid back to the supply tank. The valve’s design minimizes resistance to flow until it fills with liquid, directing most of the liquid through the main discharge line to maintain pump efficiency.

Product description

Help evacuate accumulated gasses – De-aeration Valve

Overview:

Some chemicals "off-gas" (i.e. decompose) when the pump is sitting idle; the gas accumulates and may cause the pump to lose prime. ProMinent's de-aeration valve assembly can help evacuate gases accumulated in the liquid end of the pump automatically even against system backpressure.

The de-aeration valve assembly operates by allowing any accumulated gases to exit, through the bleed valve. A small amount of liquid along with the expelled gases are channeled through the bleed valve and bypassed back to the supply tank. When gas is present in the de-aeration valve the resistance to flow through the bleed valve is relatively low. When the de-aeration valve becomes full of liquid the resistance to flow through the de-aeration valve increases dramatically, forcing most of the liquid to pass through the main discharge line.

Deaeration Valve Assembly

Installation:

1. General

Install the pump in accordance with the instructions contained in the pump operating manual. The de-aeration valve assembly must be installed directly on the outlet side of the discharge check valve.

2. Routing of Bypass Line

The bypass line should be routed back to the top of the chemical storage tank. Install the pump so the bypass line is not submerged in the chemical. It is not recommended to pipe into the calibration columns because they will overflow after a short period.

Warning: install the bypass line so any bypassed air/gas is not rerouted into the suction line.

3. Calibration

In calibrating the pump, use a graduated cylinder as the fluid source. You must collect any fluid returned through the bypass during the calibration and subtract it from the quantity drawn into the suction line.

Maintenance

  • Ensure the pump connections are correct and tight
  • Maintain a clean liquid end with no buildup of chemical crystalline material. Especially check the bleed valve and discharge ball checks.

Replacing the bleeder valve O-ring:

  • Unscrew the bleeder valve and carefully remove the O-ring with a small screwdriver
  • Fit a new O-ring into the valve port and screw in the bleeder valve and tighten to 2.2-2.6 ft. Ib. torque

Valve MNPT/PVT (A)

Order no.

Valve MNPT/PVT, DN 10

1002267

Valve MNPT/PVT, DN 15

792517

Valve MNPT/PVT, DN 20

792518

Valve MNPT/PVT, DN 25

740615

Valve MNPT/PVT, DN 32

1020031

Deaeration Valve/CPVC (B)

Order no.

Deaeration Valve/CPVC, DN 10

7740147

Deaeration Valve/CPVC, DN 15

7744695

Deaeration Valve/CPVC, DN 20

7744248

Deaeration Valve/CPVC, DN 25

7744986

Deaeration Valve/CPVC, DN 32

7745133

Air Relief Valve (C)

Order no.

Air Relief Valve

914596

Deaeration Valve Complete (D)

Order no.

Deaeration Valve Complete, DN 10

7744259

Deaeration Valve Complete, DN 15

7744260

Deaeration Valve Complete, DN 20

7744249

Deaeration Valve Complete, DN 25

7744987

Deaeration Valve Complete, DN 32

7745134

  • us_pc_4_002

Downloads for Deaeration Valve Assembly

More in the Download Centre

0 Results
Filter by document type
Application Example / Reference (0)
Brochure / Flyer (0)
Catalogue (0)
Certificate / Declaration (0)
Data Sheet (0)
Drawing / Dimensional Drawing / 3D (0)
Exploded View / Spare Parts (0)
Material Safety Data Sheet (0)
Operating Instructions (0)
Others (0)
Press Release (0)
Publication / Article (0)
Software (0)
Wiring Diagram (0)

Selected filters:

Matching downloads

Sort by Document type
Load more matches ...
No more matches available!

Unfortunately, we did not find an appropriate match.

All words written correctly?
Search again with fewer or different search terms?

Please try again later

Service Unavailable

The server is temporarily unable to service your request due to maintenance downtime or capacity problems. Please try again later.

Overview

Help evacuate accumulated gasses – De-aeration Valve

Overview:

Some chemicals "off-gas" (i.e. decompose) when the pump is sitting idle; the gas accumulates and may cause the pump to lose prime. ProMinent's de-aeration valve assembly can help evacuate gases accumulated in the liquid end of the pump automatically even against system backpressure.

The de-aeration valve assembly operates by allowing any accumulated gases to exit, through the bleed valve. A small amount of liquid along with the expelled gases are channeled through the bleed valve and bypassed back to the supply tank. When gas is present in the de-aeration valve the resistance to flow through the bleed valve is relatively low. When the de-aeration valve becomes full of liquid the resistance to flow through the de-aeration valve increases dramatically, forcing most of the liquid to pass through the main discharge line.

Technical Data

Downloads

Contact us

ProMinent Fluid Controls Ltd.


»We are always available to help. Don't hesitate to contact us.«

+1 888 709 9933 

News and Events

ProMinent Newsletter - receive latest news, customized for you! subscribe now